Dead Rabbit R folyat 😱

Questions
1

Dead Rabbit R tankom folyat a bal oldali csavarnĂĄl; Ășjonnan vettem 2 hetes, töltök fel az Ă©pĂ­tĂ©seimrƑl kĂ©pet de mindig folyĂĄs a vĂ©geredmĂ©ny kicserĂ©ltem a rögzĂ­tƑ csavarokat is Ășjra tömĂ­tĂ©ssel egyĂŒtt de nem szƱnt meg Ă­gy sem, 70/30-as lötyivel hasznĂĄlom, kinek milyen tapasztalata van ezzel kapcsolatban vagy volt nektek ilyen ? KĂ©rlek segĂ­tsetek :pray: :flushed:

IMG_1022
IMG_10221080×1920 152 KB

IMG_1015
IMG_10151080×1920 168 KB

IMG_1042
IMG_10423024×4032 1.74 MB

IMG_1048
IMG_10483024×4032 1.67 MB

IMG_1162
IMG_11623024×4032 1.17 MB

IMG_1163
IMG_11633024×4032 1.32 MB

IMG_1175
IMG_11754032×3024 1.59 MB

IMG_1176
IMG_11763024×4032 1.36 MB

IMG_1177
IMG_11773024×4032 1.35 MB

2

MegprĂłbĂĄltad esetleg, hogy a meshlapot a vĂĄlyu oldalĂĄhoz nyomkodod Ă©s utĂĄna vĂĄgod le a felesleget? Úgy rĂ©mlik az segĂ­tett illetve Ă©pĂ­tĂ©s elƑtt a vattacsĂ­kot fellazĂ­tottam egy “hullĂĄmozĂĄssal”. Ez segĂ­tett abban, hogy lazzĂĄbb legyen a vattalapok közötti tapadĂĄs.

3

azt csinĂĄltam hogy behelyezĂ©s utĂĄn az összecsĂ­pett rĂ©sznĂ©l megnyomtam a vĂĄlyĂș falĂĄnak illetve levĂĄgĂĄs elƑtt lenyomkodtam az összecsĂ­pett rĂ©sz aljĂĄt mint a gyĂĄri videĂłban :pleading_face:

4

Szia. Volt nekem is. Mindig folyt egy ido utan. 70/30 levest hasznalok en is. Mindegy volt mit csinaltam.

5

az a fura hogy csak a bal oldalt jön :person_shrugging:t4:

6

En nem tudtam ugy megepiteni, hogy ne folyt volna. Pedig nem az elso rta- m volt. De kozben en vissza tertem mtl vonalra. Probaltam benne a vattat vagas utan letomkodni az illesztesnel, gondoltam ott folyik, de max egy napot birt. Masnap mar folyt ujra.

1 Like
7

PrĂłbĂĄltam, de sajnos nincs javulĂĄs tekertem a csavarra teflon szalagot is de Ă­gy is ĂĄtfolyik :face_with_diagonal_mouth:

8

Lehet, hogy hibĂĄs tankot kaptĂĄl. Jelezd a boltnak a hibĂĄt vagy a gyĂĄrtĂłnak.

1 Like
10

Hi!

I had one too, but I think it was a bad design, I don’t think it can be built so it doesn’t leak. I tried with different wicking too (I pulled 2 layers off another cotton pad and assembled it that way), it didn’t last even a day, it leaked :thinking: It might also be a problem that its diameter is large, and the liquid pours into it.

1001×563 149 KB

Unlike a Vapefly Kriemhild 2 RMC
1000×1000 74.7 KB

Or the Wotofo smrt coil
1248×734 177 KB

While I had it, I pondered on it, that a very thin, perforated steel ring would be needed, which I would slide onto the Deck after cutting the Mesh cotton, slide it up to the edge, turned, it just needs to be very thin, but at the same time easily removable.
1000×1000 114 KB

The Voopoo PnP-VM5-VM6 0.15ohm atomizers gave the idea, where the outer sleeve is pushed on in such a way that it is half turned, thus regulating the amount of liquid flow,
1000×720 109 KB

2040×2040 140 KB

or make a steel reducer sleeve into which you put the cotton and the Mesh sheet, and the mesh sheet still fits because we narrowed it by 1mm, but this might be just enough so that it doesn’t push in too much liquid, only as much as needed. Then engrave the holes and the groove for the cotton with an engraver.
800×800 224 KB

950×535 49.4 KB


It can definitely be made so it doesn’t leak, and there’s no flavor loss either. I think it’s hopeless to have a deck like this milled with a smaller sleeve size for financial reasons, it wouldn’t be worth it, otherwise it could be done, by scanning it and milling it with CNC.

2 Likes