Tömítés probléma nem lehet?Mintha balról jobban hűlne a tekercs és azért nem kokszosodik ott annyira.Vagy az a “lyuk” is hűtheti ,amihez balról a fala hozzáér a vattához.
Én is tapasztaltam már ezt a jelenséget. Én a folyadékszállításra, a vatta sűrűségre gyanakszom ilyenkor. A vattázásnál szorulásig behúzott vatta egyik fele gondolom tömörebb az összesodort elejéhez képest.
Mióta becsületesen megritkítom a végeket, azóta ez a jelenség megszünni látszik.
Ja, nagyon szeretem az rdta-kat ízre és vattázni is. Hálás ezközök.
I have to comment because I feel there are misrepresentations. PG and VG are vaporized, or broken down into very small droplets, and enter the lungs, where some of it adheres, and the rest exits as the exhaled vapor cloud. This can be analyzed; its chemical composition is known, and perhaps its physiological effect is also known. However, the vast variety of flavorings lands in the lungs in the same way, and the lungs are not protected from their effects just because you call them natural and harmless. Because they are indeed harmless as long as you consume them as food, entrusting them to your digestive system, which is prepared to break them down. The lungs are not. The fact that it’s a natural substance doesn’t mean it can’t be poisonous; think of poisonous mushrooms, snakes, spiders… The chemical composition of the flavorings used is incredibly diverse, and our lungs have to contend with every component and their decomposition products. Let me be clear! I am now vaping after quitting smoking, but I do not downplay the significance of the chemical load this causes to my lungs.
I see these gunked-up coils. Has no one tried cleaning them in an ultrasonic cleaner yet? I clean my watch and jewelry in it too, with quite good results.
It’s a trivial item for me, so I don’t wash it (not even in ultrasonic).
The deck, tank might be worth it, sometimes I do it too. In top-airflow tanks, the channels are more complicated ![]()
Hi Gyula !
Completely unnecessary, you need to heat a few up until they’re nice and red-hot, and it will perfectly shed everything off… Of course, you also need to blow on it in the meantime…
Thanks Atti! I’m a beginner, gathering info, thinking it over…
When it fires up, I always get startled
though it’s already quite thick
.

Just reporting, I’ve tried!
And it worked!
A couple of firings afterwards were enough and lo and behold, it works.
![]()
Hi Gyula! Welcome to our community! ![]()
No, I don’t tend to distort things. If you read back, you can see that I also pointed out the risks. It’s not by chance that the essence of the article is to keep the coil clean, as it can cause serious problems, which can lead to a state that is no longer physiological, but pathological, or morbid.
Specifically, vape flavor is suitable for inhalation (too), as it passes EU tests. Tests such as composition analysis, which detects if something is present that shouldn’t be there (meaning it can cause a pathological state). Physical and chemical tests, which examine boiling point, viscosity, and water content, largely for the protection of the atomizer, so that you don’t see an image in the deck like the ones you’ve seen under this article so far.
This is followed by toxicological risk assessment and emission tests, which examine the vapor of the finished liquid after it has been exhaled, often using a standardized smoking machine to simulate consumer usage.
I would also mention that one of the fantastic properties of our lungs is that they are self-cleaning, so if something that really doesn’t belong there accidentally gets in, the lungs expel it. ![]()
Yes, pathological. That term didn’t come to mind. For a bit of humor: even the bologna was examined, completely harmless; upon entering the lungs, we can rightly expect them to expel it. ![]()
Hi everyone. I haven’t been here for a while. Since nicotine was forced into the tobacco shops, I don’t buy anything else. I’ve quit all sorts of concoctions. Tobacco extract, the real kind, is only sold by the Italians and the Maltese. I’m only writing here in the forum/thread because I’m sharing my experience. Unfortunately, even a weak vape has some kick. Not as much as tobacco extracts, only half as much. With glycerin and PG + nic shot, the cotton still needs to be changed 1-2 times a week. I never vape any of them above 10 Watts. Still.
Hi Mefeca!
Long time no hear, hope you are well and everything is okay. ![]()
Regarding gunking, if you buy the nicshot at a shop, and if not, it’s still not good if it gunks up this much. It should last at least 1 month, and even then, only the parts of the cotton directly under the coils should be light brown.
My first tip is that your coil is too tight. It might be gunking up this much because in a too-tight coil, the liquid can no longer act as a coolant. If your coil were looser, the liquid (or in this case, base liquid/e-liquid base) in the cotton would not reach the coil’s temperature during firing, therefore it would also serve well as a secondary cooling agent. But this way, it can only burn.
The second is that there’s not enough airflow. It might be that because of less airflow, your coil is not cooling well, therefore the wire is cooling poorly, which makes the vapor hot and the liquid quickly boils, almost burning. If the tank’s cooling (airflow) is good, then there’s no chance for the base to burn onto the coil.
The third is that the coil is too high. It might even happen that due to a coil placed too high, the base burns onto the coil immediately, because it gets air late.
By the way, I don’t know what the ingredients of tobacconist nicshots are, but perhaps try for a short while to use your tank the same way but with a liquid without nicshot, using just the base. If it doesn’t gunk up, or only less so, then something in the nicshot is causing this. If it continues to gunk up the same way, then change the coil build as I’ve explained.
Hi. Thanks for the reply. I’m doing fine otherwise. Retired for 4 years now. I’m not satisfied with the new look of the site. You can’t even see who is online, and searching through the topics feels more difficult as well. Unfortunately, I can’t change much about my coil building. I only have one working regulated mod that Isti sent me, a Vaporesso Swag2. All the others are mechs, which means I have to stick to 1 ohm, no matter what wire I use for building. This is ten wraps of SS316 28GA wire on a 2.5 mm diameter. I usually use a razor blade to space out the wraps. I’ve been doing it this way for 8 years now, so I can’t really change it. The height of my coil is exactly 1 mm from the airflow hole. Don’t tell me that’s too much. For atomizers, I use the Dwarv series and the By-ka V7. I think they are quite airy. The problem with the base liquid is that for about a year I was vaping with a 50/50 VG/PG ratio, but my nose gets sore. The AI suggested I vape with less PG, but then the glycerin is too thick. I don’t even dare to use the By-ka V8 atomizer at all. It’s a catastrophe compared to the V7. Everything is tighter on it, so it’s constantly dry-hitting, and the reverse-threaded top cap is the number one reason for tank sections breaking. Because when you open it, it tightens the tank section until it cracks, and it can only be removed by breaking it. I’m discarding that one. True, it’s one of the ones I bought with my own money, so no one will be offended if I write here that I’m throwing it away. Or it will just stay on the shelf as an ornament. The V7, which was also sent by Isti, or purchased for me from him by János, is still usable. It is slightly prone to leaking (Isti was the one who complained about it), which, with my thick glycerin and dense wicking, doesn’t leak at all.
I saw that you wrote about MellowDev e-liquids somewhere. At the tobacco shop I go to, they have 18 mg/ml MellowDev nicshots. I buy 4 of the 10 ml bottles at once, and I try to make them last for 2 weeks. I want to divide them into 6 parts, but I always run out at the fifth one. Even though I mark the bottles into 6 parts with a felt-tip pen, that one dose always gets lost somewhere while pouring. That 10 ml is terribly little. And trying to divide it into 6 parts is a nightmare. But it’s calculated so that 1 ampoule should last about 4-5 days. Of course, since I also vape at night, 10 ml of diluted liquid isn’t enough for just one day.
Hi Mefeca!
Reading the quoted sentence, I would like to send you a great, functional mod of this type that I rarely use anymore:
It can be used in both single/dual battery and squonker modes.
What is your take on this idea?
Best regards: Zolee
Thanks, but mechanical mods don’t have issues where I take them out, take a hit, and get a burnt taste because they weren’t locked and accidentally got set to max power in my pocket. They don’t do things like displaying “Low Battery” at 90% just because the poor battery isn’t in top shape anymore. But in MTL, a mechanical mod can easily handle 2.5 Amps. If there’s poor contact, regulated mods just restart and reset their settings. I also had a dual-battery Tesla Poker which was great for the usual 1-2 years, but then the screen started to fade. I wanted to add an LED behind it for backlighting, but the back was black, you couldn’t see what was illuminating it, and when I drilled into the plastic, the screen got ruined. I have 3 others that just simply started smoking, likely due to liquid damage. Somehow I don’t have much luck with electronics, but I don’t even need them. Aside from being able to show you the resistance of your coil in ohms, they just cause trouble. If they get a little bit of condensation on them, they start smoking right away.
Hi Ferenc!
I highly recommend that you accept the mod Zoli has offered you.
Unfortunately, the Swag won’t last forever either, as the plastic part under the fire button breaks from one moment to the next, rendering the mod unusable.
(I’ve already had two break; so far I’ve been able to replace them, but if the third one currently inside breaks, I unfortunately won’t be able to use it anymore).
